-
Recent Posts
Recent Comments
- metal_musings on Steel Bladed Knives
- Aneeq Iftikhar on Steel Bladed Knives
- metal_musings on Traditional Baskets
- George my number is 206-551-3761 on Traditional Baskets
- metal_musings on Steel Bladed Knives
Archives
- March 2022
- September 2020
- August 2020
- April 2020
- December 2019
- February 2019
- June 2018
- May 2018
- October 2017
- August 2017
- July 2017
- June 2017
- March 2017
- December 2016
- November 2016
- October 2016
- September 2016
- August 2016
- July 2016
- April 2016
- March 2016
- January 2016
- December 2015
- October 2015
- September 2015
- July 2015
- June 2015
- April 2015
- March 2015
- January 2015
- December 2014
- November 2014
- October 2014
- September 2014
- August 2014
- July 2014
- June 2014
- April 2014
- March 2014
- February 2014
- December 2013
- November 2013
- October 2013
- September 2013
- August 2013
- July 2013
- June 2013
- May 2013
- April 2013
- March 2013
- November 2012
- October 2012
- July 2012
- May 2012
- April 2012
- March 2012
- February 2012
- January 2012
- December 2011
Categories
Meta
Category Archives: Carving
Clockwork Trilobite – Part 4
Today I need to make the last little gear, solder everything together and do the initial shaping. Above, I’m using a computer printout as a pattern for the tiny gear, and drilling the starting holes. I used a scan of … Continue reading
Posted in Carving, Jewelry, Pendant, Steampunk
Tagged carving, engraved, engraving, fabricated, fabrication, punches, shibuichi, steampunk
Leave a comment
Clockwork Trilobite – Part 3
In order for the parts to solder well, I need to flatten all the mating surfaces – the top surface of the bottom plate, the bottom surface of the top plate, and the bottom of the gears (there’s a parsing … Continue reading
Posted in Carving, Jewelry, Pendant, Steampunk
Tagged carving, engraved, engraving, fabricated, fabrication, punches, shibuichi, steampunk
Leave a comment
Clockwork Trilobite – Part 2
Today was just a lot of sawing. A lot…I had forgotten how gummy and resisting sterling silver could be, especially in thicker pieces. Now I remember why I much prefer sawing, engraving and carving in steel… Above are the two … Continue reading
Posted in Carving, Pendant, Steampunk
Tagged engraved, engraving, fabricated, fabrication, punches, shibuichi, steampunk
2 Comments
Clockwork Trilobite – Part 1
Here’s the start of a commission for an engraved and carved silver trilobite, with copper gears. Above, I’m weighing out scrap sterling silver (looking for about an ounce). The scrap needs to be clean, and free of any solder. If it … Continue reading
Posted in Carving, Jewelry, Pendant, Steampunk
Tagged carving, engraved, engraving, fabricated, fabrication, punches, shibuichi, steampunk
Leave a comment
Nazgul Holdout Stiletto – Part 5
Today, I finally finished up the sheath for this little dagger. Above you can see the leather liner and the small piece of goat rawhide I’ll use for the outside. I’ll have to soak the rawhide in warm water for … Continue reading
Posted in Carving, Engraved Knife, Misericordia
Tagged carving, dagger, engraved, engraving, fabricated, fabrication, knife
2 Comments
Nazgul Holdout Stiletto – Part 4
Now it’s time to make a sheath for this dagger. I’m (loosely) basing the sheath on the Bell Dirks. Bell Dirks are contemporaries of of the famous Bowie knives, and were highly decorated, long slim daggers typically carried by gamblers … Continue reading
Posted in Carving, Engraved Knife, Misericordia
Tagged carving, dagger, engraved, engraving, fabricated, knife
Leave a comment
Nazgul Holdout Stiletto – Part 3
Continuing on, I’ve been working on the pommel of the blade carving a Nazgul helmet on the four-sided taper. Above, I’ve engraved the guide lines on all four sides, with spooky helmet on the “front,” and the icky “winged beasty” … Continue reading
Posted in Carving, Engraved Knife, Misericordia
Tagged carving, dagger, engraved, engraving, knife
Leave a comment
Nazgul Holdout Stiletto – Part 2
I finished twisting and forging the blade and handle, so above is the result. The entire dagger is about 8 inches long, and should appear above at full size in your monitor (I hope…). Above, I carved my usual handle/blade … Continue reading
Posted in Carving, Engraved Knife, Misericordia
Tagged carving, dagger, engraved, engraving, knife
Leave a comment
Nazgul Holdout Stiletto – Part 1
Well, now for something a bit different. I came up with this idea watching the Lord of the Rings movies, and was picturing the head Nazgul (the Witch King) sitting in the bar playing poker with his minions, and wondering … Continue reading
Posted in Carving, Engraved Knife, Misericordia
Tagged carving, dagger, engraved, engraving, knife
2 Comments
Hummingbird Art Basket – More Adventures in Press Forming
Here’s another little art basket my wife and I collaborated on. This little hummingbird basket is about three inches in diameter. The basket itself is made from ziricote (the rim and base) and is woven with waxed Irish linen. The … Continue reading
Posted in Art Basket, Carving, Press Forming, Steampunk
Tagged antler, Basket, fabricated, fabrication, Press Forming, punches
Leave a comment